FlickerMarine · Made to measure in Shanghai

Clear photos and measurements make a better starting point

This guide helps you prepare initial information. Send photos and any measurements you have; our team will identify further checks for your boat and its layout.

Prepare your photos

Start with photos, then add dimensions

01

Overall views show the position

Include the boat and the area around the part, showing rails, brackets, seats and nearby equipment to help establish the coverage required.

02

Different angles show the shape

Photograph the front, rear, both sides and top of the same part. Include brackets, cables and fastenings hidden behind it.

03

Close-ups show the connections

Show zippers, straps, snaps, openings and corners clearly. A ruler can be included in the photo, but please also write down the measurement.

Keep measurements consistent

Use these habits when sharing dimensions

01

Add a unit to every number

Use mm or cm and label the unit clearly. Keep the same unit throughout each set of measurements where possible.

02

Mark where each measurement starts and ends

Mark points such as A-B on a photo, and say whether the dimension is a straight distance, a length along a curve or a circumference.

03

Send the actual reading

Do not add fitting ease or seam allowances yourself. Any allowances are agreed as part of the production specification.

04

Describe the fitted position

Say whether equipment is folded, removed or left installed. Measure it in the same position it will be in when covered.

Organize the essentials in one checklist

Prepare information for each part

Photo and measurement checklist by part
PartInitial dimensionsPhotos neededPoints to note
Boat coversBoat length, beam, coverage height and positions of equipment above the deckBow, stern, both sides and protruding partsWhether top-mounted equipment is removed; mooring points and coverage limits
Console / seat coversWidth, height, depth and protruding armrests, backrest or rear stationFront, rear, sides, top and clearance belowDistinguish a protective cover from replacement upholstery
T-top / extended shadeCanvas outline, spacing of support points and the path along curved areasThe complete frame, all corners and connection pointsDo not mix straight distances with measurements along a curve
Clear enclosuresMark each panel's boundaries, connections and openingsEach panel fitted on board, zipper ends and fastening pointsNumber the panels and mark their orientation; do not stretch aged clear panels
Outboard coversEngine cowling shape and coverage; provide the full engine modelThe engine from several angles, showing its installed and tilted positionsState whether the cover is for storage or another use
Fish finder / equipment coversEquipment body, brackets, knobs and space occupied by cablesFront, rear, brackets and cable-routing close-upsCheck the actual installation even when the model is known
Fender covers / storage bagsFender shape, length and circumference; or available storage spaceItem shape, rope holes and mounting positionDescribe access and what will actually be stored

Start with an assessment if information is incomplete

Discuss these situations before measuring further

01

Curved surfaces or complex corners

A single length and width may not be enough. Show the outline, corners and measuring path clearly, and add cross-section information if needed.

02

A distorted old item

Provide photos of it fitted on board and the actual measurements. Mark tight, loose or missing areas.

03

Hard-to-reach areas

Send photos first and identify the areas you cannot measure. Do not climb into unsafe positions or reach into running equipment to obtain measurements.

Use this as a starting point

A message you can send to our team

Part to be made: ______

Intended use and fitted position: ______

Available dimensions and units: ______

Measurement locations / photo numbers: ______

Required openings or fastening points: ______

Unconfirmed details or changes requested: ______

FlickerMarine · Shanghai factory

Tell us what you need.
Let's work through the details.

New covers, replacement canvas or refurbishment:
send us your photos and requirements to discuss a suitable plan.

Both numbers accept calls and can be used to add us on WeChat.

Copy a number and search for it in WeChat under Add Contacts.

WeChat QR codes to be addedFor now, add us by phone number
Phone / WeChat

Products

Details we can discuss

    What to prepare

      Dimensions, fabric, construction and components are confirmed in the final proposal. Specifications and prices are agreed for each project.

      Start your consultation with these details

      New custom canvas inquiry

      Contact our team

      Copy the number, then open WeChat and add a contact.

        Edit this checklist, copy it and send it to our team on WeChat. This page does not submit or save your details.